How to install an SSD in your PC


how install ssd pc samsunginstall

Samsung

Installing an SSD is one of the most straightforward upgrades you can do to your PC — the only one with fewer steps is installing new memory. That makes it a great way to try out upgrading your PC by yourself, and we’re here to help. Just follow the steps below, and you’ll have a great new SSD in your PC in no time.

Here’s how to do it.

Buying the right SSD

Before you can install an SSD, you need to buy the right one for your PC. If you’ve already done that, skip ahead to the install instructions below, but if you haven’t, be sure to give our guide on how to buy an SSD a read. It will walk you through buying an SSD that will physically fit in your PC and is compatible with it. It will also give you advice on speed and capacity to help you get the best SSD for you.

How to install an NVMe SSD in your PC

Most modern SSDs are NVMe drives using the M.2 form factor, and most PCs come with dedicated slots for those. If you have an older 2.5-inch SATA SSD you want to install, check out the section below.

Step 1: To install an NVMe SSD in your PC, shut your computer down and unplug all the cables, then place it on a desk or other easily-accessible surface with adequate lighting.

Step 2: Remove the case side panel using the rear screws.

Step 3: Before touching any internal components, ground yourself by attaching an anti-static wristband, or by touching some conductive portion of the case or power supply chassis. Do this periodically while working in your PC, and ideally, wear rubber-soled shoes while doing so — especially if you’re standing on carpet.

Anti-static wristband on a man's wrist.

Bill Roberson / Digital Trends

Step 4: Locate a spare NVMe SSD slot on your motherboard. These are often found in the middle of the board, but can also be farther down, nestled among the PCIExpress slots. It may be underneath your graphics card in some cases — you may have to remove the GPU to get access.

Step 5: Remove the retaining screw(s) and lift off any pre-installed heatsinks.

ASRock Taichi B650E motherboard
In this case, the ASRock motherboard has a heatsink on top of the SSD slot.

ASRock

Step 6: Angle the SSD into the slot at around 45 degrees, and gently push it in until you feel a gentle click. Then press the other end of the SSD down, until it rests against the retaining screw hole. Then use the retaining screw to secure the drive in place. If necessary, re-attach any heatsinks that were in place before the install.

Installing a Samsung SSD.

Samsung

Step 7: Before closing up your PC, plug in the cables again and boot it up. Check the BIOS, and in Windows to see if the new SSD is detected. If not, you may need to initialize it within the Windows Disk Management utility.

If it still doesn’t show up, follow these steps to fix it.

Hard drive slot in PC.

Bill Roberson / Digital Trends

How to install a SATA SSD

SATA SSDs can still be a great way to add capacity and speed to a PC, especially if you’re on a tight budget. They take a little more effort to install, but it’s still straightforward. Here’s how to do it.

Step 1: Turn off your PC, unplug all the cables, and remove the side panel. Then place it on a desk or easily-accessible surface with adequate lighting.

Step 2: Locate a spare 2.5-inch drive bay. If you don’t have one, either remove an existing drive, or be prepared to use some tape or other method for securing your SSD still in the base of your case, or against a side panel. While SSDs aren’t susceptible to physical damage like hard drives are, you still don’t want it rattling around if you need to move your PC.

Step 3: Locate a spare SATA power connector. It will have an L shape. Plug that into the appropriate power port on your SSD. Then grab a spare SATA cable — you should have gotten one with the SSD or your motherboard — and plug it into the SSD. Then secure the other end into a free SATA slot on your motherboard. It should be located somewhere along the front edge of the board.

SATA power cable connected to hard drive.

Bill Roberson / Digital Trends

Step 4: Before closing up your PC, plug in the cables again and boot it up. Check the BIOS as well as Windows to see if the new SSD is detected. If not, you may need to initialize it within the Windows Disk Management utility.

If it still doesn’t show up, follow the steps linked to in the NVMe section above and you should be able to fix it.

Got a laptop that needs a storage upgrade? Here’s how to install an SSD in your laptop.








Source link